ATX PWS-1419T Specifications

IndustrialPWS-1419TPortable ComputerSystem Assembly GuideA Technical Guide for System Integratorsand Service Technicians

The KeyboardThe subassembly comes with a mechanical switch keyboard with an integrated touch paddevice. The signal cable is conceal in the fillister

1. Opening The Chassis 12Removing the Back Cover 12Removing the Card Stabilizers 12Identifying the Internal Parts 12Removing the Drive Ca

Open the chassis Removing the Back CoverFace the back of the chassis. Remove all screws as shown. There are 7 screws along theperimeter of the back

Installing The BackplaneMake sure that at no time you are working on any electrical or electronic components while anypart of the system is energized

find the mount point of the backplaneinsert the stand offsThread clock-wise to insert the standoffreverse to take off the stand offYour package comes

Connecting the power ConnectorThe plug from the power supply will only insert in one orientation. Push down firmly makingsure the hook on the termina

secure the hard disk to drive cage with screw# 5, insert washer #3 between cage andscrew, same with the other side secure the floppy disk to drivr ca

Installing the DriverCageStep 1. Carefully put the drive cage back into the chassis.Step 2. Plugging the case fan power conecttor into the interface

Installing the SBC Setting your SBC JumpersBefore installing the motherboard in the chassis, install the CPU and set any dip-switch orjumper on the S

Connect the signal cable and chassis cablebefore fix the SBCFix the SBC with screw #2 Installing the Add-on CardsThe chassis has 10 slot openings supp

The information contained in this document is believed to beaccurate. However, no responsibility is assumed for its use,nor for any infringements of p

Step 3. Slide each clip so they come in contact with the top edge of the add-on cards.While holding the clip firmly against the card edge, tighten the

1. Connect the VGA Connector2. Connect the other connectors for other device such as Ethernet, Audio device… Closing the Back CoverReinstall the bac

Using The System ControlsStarting your System 23Systems with ATX Power Supply 23Systems with AT Power Supply 23OSD Controls 23Adjusting the OS

Starting your SystemBefore starting your system, plug in the power cord and make sure the video and input deviceconnectors are plugged in. Release t

Contrast MenuContrast: Manual adjustment the contrastSub-CONTRAST: Manual adjustment of individual RGB channel contrast. Position MenuH-size: Adjus

Appendix A.Trouble Shooting Techniques 26 No screen after pressing front power switch 26 Power supply fan not spinning: 26 Power supply fan i

Trouble Shooting Techniques No screen after pressing front power switch Power supply fan not spinning:Check power source.Check power cord connectio

LCD SCREEN works fine in Windows but acted funny when running certain pro-grams or games:The built-in Intelligent Analog-Digital conversion board (AD

Appendix B: LCD VIDEO ControllerIntroduction 29Safety Precautions 30Identifying the Components 30Main Board 30Main Board ASIC Features 31LVD

IntroductionThe LCD video controller subassembly is an “in-monitor” design build around a highperformance ASIC technology that enable the display of

Specification 4Before You Start 5 Precau

The light source for most flat panel displays is a cold cathode fluorescent backlight.These backlights run on high AC voltage provided by an inverter

1 Jumper for 3.3V or 5V TFT panel. 15 Analog video input connector2 DC power output 16 Reserved3 DC p

Automatic ADC Sampling Phase Optimization-Performs measurements so that firmware can automatically optimize the ADC samplingphase.Optimized Panel Cloc

OSD Push Button BoardThe OSD menus and parameters are accessed by 4 push buttons . Configuring Your ControllerWhile your LCD controller is designed

OSD ControlsThe LCD controller includes an integrated RAM-based OSD controller. Through four frontpanel controls you can view adjustable features of

POSITIONH-SIZE: Adjustment of the vertical image sizeCKOCK PHASE: adjustment of the ADC sample pixel clock.H. POSITION: Adjusts the horizontal image

Getting Started General Features Support passive backplane form factor platforms. ABS plastic housing with aluminum internal chassis. 14.1” Hig

Before You StartThe major component of the subassembly is the chassis, which comes in two models—9 xISA slot or 4 x PCI, 5 x ISA slot Passive Backplan

VentilationThe chassis comes with three intake fans and one power supply exhaust fan providingcooling and air flow. When operating the system, never

Optional Slim CD ROM Disk1. Slim CD ROM interface board2. CD ROM power cable (interface to power supply)3. Audio cable (interface board to

PWS 1419T Side ViewsUse the photo below to identify components and I/O ports that are accessible from the twosides of the BP-10 chassis. The illustrat

Front ViewPower LEDHDD LEDTFT LCDNum LockScroll LocckCaps LocckLED IndicatorTouch Pad Anti-slipperRubber KnobPush theKeyboard Latches tocent